PROTO-PASTA HTPLA 500G IRIDESCENT ICE CLEAR
PTPHTP21705-ICE
Item Number: PTPHTP21705-ICE
HTPLA out performs PLA, ABS, and Polyesters like PET!
Proto-pasta's HTPLA v2.0 is better than the original kickstarted version. This new formulation is higher performing and lower cost. HTPLA prints similar to standard PLA but is "Hella Tough" and can be "Heat Treated" for "Higher Temperature" resistance. This durable PLA has a theoretical Heat Deflection Temperature (HDT) of more than 140C (285F) after heat treating though in our experience 120C or more was practically attained. This means HTPLA parts maintain strength and form to much higher temperatures than PLA, ABS, or Polyesters like PET which loose structure as soon as 55C and by 100C.
How do you "Heat Treat" for maximum performance? Bake your parts into a oven until you see a change from translucent to opaque. Yes, there is an obvious visual change indicating the improved performance! We had good luck in a lab oven at 110C (230F) for an hour or less. We recommend leaving the supports on your parts, placing them on a non-radiating surface (like glass, ceramic, or composite), and letting them cool in the oven to minimize distortion. Parts can be baked at a lower temperature (though must be above 60C for any change to occur) for a longer time with less risk of unwanted deformation.
Available in 1.75 & 2.85 (3) mm diameter
Colors include Iridescent Ice & Silver Smoke
500g 8" diameter spool only
No abrasive fillers so expect normal wear with standard nozzles.
In our experience, good results were achieved using standard PLA parameters with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required. Some shrinkage and distortion may occur in the annealing process, so larger or dimension critical parts may need to be scaled larger to compensate or printed in our more stable, lower shrink Carbon Fiber version.
#3DBenchy - The jolly 3D printing torture-test by CreativeTools.se by CreativeTools
Published on April 9, 2015
www.thingiverse.com/thing:763622
All Proto-pasta HTPLA/ZYLTECH PLA Benchy models were printed with a Prusa I3 Mk3s w/ PrusaSlicer
& Pretty PLA v4.0 Profiles
All ZYLTECH PETG Benchys were printed with a Pruisa I3 MK3s w/ PrusaSlicer & Pretty PETG V3
Profiles
HTPLA out performs PLA, ABS, and Polyesters like PET!
Proto-pasta's HTPLA v2.0 is better than the original kickstarted version. This new formulation is higher performing and lower cost. HTPLA prints similar to standard PLA but is "Hella Tough" and can be "Heat Treated" for "Higher Temperature" resistance. This durable PLA has a theoretical Heat Deflection Temperature (HDT) of more than 140C (285F) after heat treating though in our experience 120C or more was practically attained. This means HTPLA parts maintain strength and form to much higher temperatures than PLA, ABS, or Polyesters like PET which loose structure as soon as 55C and by 100C.
How do you "Heat Treat" for maximum performance? Bake your parts into a oven until you see a change from translucent to opaque. Yes, there is an obvious visual change indicating the improved performance! We had good luck in a lab oven at 110C (230F) for an hour or less. We recommend leaving the supports on your parts, placing them on a non-radiating surface (like glass, ceramic, or composite), and letting them cool in the oven to minimize distortion. Parts can be baked at a lower temperature (though must be above 60C for any change to occur) for a longer time with less risk of unwanted deformation.
Available in 1.75 & 2.85 (3) mm diameter
Colors include Iridescent Ice & Silver Smoke
500g 8" diameter spool only
No abrasive fillers so expect normal wear with standard nozzles.
In our experience, good results were achieved using standard PLA parameters with standard build surface preparation (blue tape, glue stick, or BuildTak). No heated bed required. Some shrinkage and distortion may occur in the annealing process, so larger or dimension critical parts may need to be scaled larger to compensate or printed in our more stable, lower shrink Carbon Fiber version.
#3DBenchy - The jolly 3D printing torture-test by CreativeTools.se by CreativeTools
Published on April 9, 2015
www.thingiverse.com/thing:763622
All Proto-pasta HTPLA/ZYLTECH PLA Benchy models were printed with a Prusa I3 Mk3s w/ PrusaSlicer
& Pretty PLA v4.0 Profiles
All ZYLTECH PETG Benchys were printed with a Pruisa I3 MK3s w/ PrusaSlicer & Pretty PETG V3
Profiles